DEVICES YOU NEED TO INSTALL A NEW BATHTUB

Devices You Need to Install a New Bathtub

Devices You Need to Install a New Bathtub

Blog Article

Click Here To Read More

Were you interested in ideas concerning Installing A Bathtub?


Installing A Bathtub
Setting up a bath tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old tub with a brand-new one is also a reasonably hard project. If the old tub is easily obtainable, the project can move rapidly; if you have to open up a wall surface to get rid of the old bathtub and position the brand-new bath tub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the new one. See to it you have actually qualified on your own for the job as well as fit trying it. As opposed to employing a service provider to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly aid you install a new bath tub in your bathroom if you have currently bought a new bathtub and also don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list ought to make up the following:
  • New Bath tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Blade

  • Measuring tape

  • Pipe Caps


  • Preparing for the Setup


    First of all, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the faucet comes with a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
    Fit the adaptable faucet connectors to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
    Connect the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom need to now be ready to be fitted in its final setting.

    Removing Old Touches


    If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is detach the water system. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of removing the existing taps can be quite troublesome because of the restricted gain access to that is commonly the situation.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the remaining water that will come from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will certainly need to be cleansed of any kind of old securing compound.
    Before moving on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new taps to fit.

    Mounting the Bath tub


    Utilizing the two wooden boards under its feet, position the bath tub in the needed setting. The wooden boards are helpful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small factors.
    The following objective is to make sure that the bathtub is leveled all round. This can be attained by inspecting the level as well as adjusting the feet on the tub until the level reads degree.
    To install faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Switch on the water and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and additionally check the overflow electrical outlet and the typical electrical outlet for leaks.
    Ultimately, fix the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the bath tub ought to wait up until the bath tub has been made use of at least once as this will certainly resolve it into its last placement.

    Fitting New Taps


    If the tails of the new faucets are plastic, after that you will need a plastic adapter to prevent damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipes.
    If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
    Next off, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the faucet in position with the manufacturer supplied backnut. When the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet ends first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been attached.

    Tiling Around the Bathtub


    In the area where the bath satisfies the tile, it is required to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to assimilate your components and also installations. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to enable the activity experienced when the tub is in use. The sealer can split relatively early if you do not take into account this activity prior to sealing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the market. It is suggested to fit the ceramic tiles using waterproof or water resistant glue as well as cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    Do you like more info about How to Install a Bathtub? Create a short review down below. We will be pleased to hear your ideas about this content. We hope to see you back again in the future. Appreciated our piece of writing? Please share it. Help other people locate it. Thanks for taking the time to read it.




    Schedule Now!


    Report this page